top of page

Home › Resources › Coil Spring Glossary

Oshkosh Coil Spring coil spring glossary PDF cover

RESOURCES · REFERENCE

Coil Spring Glossary: Spring Terms & Definitions

Common terms used when specifying compression, extension and torsion springs, from active coils and spring index to initial tension and solid height. Symbols in orange are the ones used on drawings and in spring calculations.

JUMP TO

Select a letter to find a term, or use your browser’s search (Ctrl+F) to look for a specific word.

SPRING TERMS A–Z

Spring Terminology for Compression, Extension & Torsion Springs

Use these definitions when reading a spring drawing, filling in a quote request or using our online spring calculator. If a term on your print isn't here, call us and an engineer will walk through it with you.

A

Active coils (n)

Those coils which are free to deflect under load.

Angular deflection

Rotation of the legs of a torsion spring from the free position under load, usually expressed in degrees.

Angular relationship of ends

The relative position of the plane of the hooks or loops of extension springs to each other.

B

Baking (hydrogen relief)

Heat treatment performed promptly after plating or pickling to drive out absorbed hydrogen and reduce the risk of hydrogen embrittlement. Typically about 375–425°F (190–220°C) for four hours or more, per ASTM B850.

Body length

Length of the coiled body of an extension spring, excluding hooks or loops. For a close-wound spring, approximately (total coils + 1) × wire diameter.

Buckling

Bowing or lateral deflection of compression springs when compressed, related to the slenderness ratio (L/D).

C

Close-wound

Coiled with adjacent coils touching.

Closed and ground ends

Closed ends

Closed length

Coatings

Non-plated finishes such as powder coat, e-coat, black oxide, zinc flake or oil, applied for corrosion protection or appearance.

Coils per inch

Compression spring

An open-coiled helical spring that resists a compressive force applied along its axis and becomes shorter under load.


Compression springs →

Conical spring

A compression spring whose coil diameter tapers from one end to the other, so coils can nest inside each other for a lower solid height. Often has a variable rate.


Conical springs →

Crossover loop

Extension spring end in which the last coil is bent across to the center of the spring and then formed into a loop. Lower stress than a machine loop.

D

Dead coils

End coils of a compression spring that do not deflect under load, such as the closed coils of squared ends.

Deflection (F)

Motion of spring ends or arms under the application or removal of an external load (P).

Die spring

A heavy duty compression spring, usually made from rectangular or shaped wire, designed for high loads in a small space in dies, molds and tooling.

​

Die springs →

Direction of coiling (helix)

Right hand or left hand, as with screw threads.

E

Elastic limit

Maximum stress to which a material may be subjected without permanent set.

Endurance limit

Maximum stress at which any given material will operate indefinitely without failure, for a given minimum stress.

Extended hook

Extension spring end in which the hook or loop is set out from the spring body on a straight length of wire to reach an attachment point.

Extension spring

A close-wound helical spring, usually with hooks or loops at each end, that resists a pulling force and becomes longer under load. Often wound with initial tension.

​

Extension springs →

F

Fatigue life (cycle life)

The number of load cycles a spring can withstand before failure at a given stress range. Influenced by material, stress range, surface condition and processes such as shot peening.

Free angle

Angle between the arms of a torsion spring when the spring is not loaded.

Free length (L)

The overall length of a spring in the unloaded position.

H

Helix

The spiral form (open or closed) of compression, extension and torsion springs.

Hooks

Open loops or ends of extension springs.

Hydrogen embrittlement

Hydrogen absorbed during electroplating or pickling of carbon and alloy steels, tending to make the spring material brittle and susceptible to cracking and failure, particularly under sustained loads. Baking promptly after plating reduces the risk. 

 

See Baking

Hysteresis

The mechanical energy loss that always occurs under cyclic loading and unloading of a spring, proportional to the area between the loading and unloading load-deflection curves within the elastic range of a spring.

I

Initial tension

The force tending to keep the coils of an extension spring closed, which must be overcome before the coils start to open. A design consideration generally specified only as a reference value.

Inside diameter (ID)

Diameter of the cylinder enveloping the inside surface of the coils; outside diameter minus two wire diameters.

L

Legs

The straight ends of a torsion spring that extend from the body and through which the load is applied. Also called arms.

Length inside hooks

Distance between the inside surfaces of the hooks or loops of an extension spring in the free position. The usual way to specify extension spring length.

Load (P)

The force applied to a spring that causes a deflection (F).

Loops

Coil-like wire shapes at the ends of extension springs that provide for attachment and force application.

M

Machine loop

Extension spring end formed by bending the last coil up so the loop lies in the plane of the spring axis. The most common and economical end.

Mandrel (arbor)

The rod over which a spring is coiled, or the shaft a torsion spring is mounted on in service. A torsion spring’s body diameter decreases as it winds up, so the mandrel must clear the reduced inside diameter at full deflection.

Mean coil diameter (D)

Outside spring diameter (OD) minus one wire diameter (d); equivalently, inside diameter (ID) plus one wire diameter.

Modulus in shear or torsion (G)

Coefficient of stiffness used for extension and compression springs.

Modulus in tension or bending (E)

Coefficient of stiffness used for torsion and flat springs (Young’s modulus).

Moment (M)

N

Natural frequency (surge)

The lowest frequency at which a spring vibrates freely between its ends. Operating near this frequency causes surge, which raises stresses and can cause early failure; it should be well above the operating frequency.

O

Open ends, ground

“Open ends, not ground” followed by an end grinding operation.

Open ends, not ground

Ends of a compression spring with a constant pitch for each coil.

Outside diameter (OD)

Diameter of the cylinder enveloping the outside surface of the coils.

P

Passivating

Acid treatment of stainless steel to remove contaminants and improve corrosion resistance.

Permanent set

A material that is deflected so far that its elastic properties have been exceeded, and does not return to its original condition upon release of load, is said to have taken permanent set.

Pitch (p)

The distance from center to center of the wire in adjacent active coils. Recommended practice is to specify the number of active coils rather than pitch.

Plating

An electrodeposited metal coating, such as zinc or nickel, applied for corrosion protection or appearance. High-strength spring steels require baking after plating.

Preset

The process of compressing a spring to solid height to remove set, so it holds its free length in service. Usually specified only when the application requires it.

R

Rate (R)

Change in load per unit deflection, generally given in pounds per inch (or N/mm). For torsion springs, change in torque per degree of rotation.

​

Calculate spring rate →

Remove set

Residual stress

Stresses induced by set removal, shot peening, cold working, forming or other means. These stresses may or may not be beneficial, depending on the application.

S

Set

Permanent distortion which occurs when a spring is stressed beyond the elastic limit of the material.

Shot peening

Bombarding the spring surface with small steel shot to clean it and induce beneficial compressive residual stresses, thereby increasing fatigue life.

​

Shot peening services →

Slenderness ratio

Ratio of spring length (L) to mean coil diameter (D).

Solid height (H)

Length of a compression spring when under sufficient load to bring all coils into contact with adjacent coils.

Spring constant

Spring index (C)

D/d, the ratio of mean coil diameter to wire diameter. The preferred range is about 4 to 12. Springs with an index below 4 are difficult to coil, and those above about 16 tend to tangle and are harder to hold to tolerance.

Squared and ground ends

End finish for compression springs where the pitch of the end coils is reduced so that the end coils touch, and the end is then ground to provide a flat end.

Squared ends

As squared and ground ends, except not ground.

Squareness of ends

Angular deviation between the axis of a compression spring and a normal to the plane of the ends.

Squareness under load

As in squareness of ends, except with the spring under load.

Stress (S)

The internal force per unit area in the spring wire under load, usually given in psi or MPa. Compression and extension springs are stressed in torsion; torsion springs are stressed in bending.

Stress range

The difference between the stresses at the minimum and maximum operating loads; a key factor in fatigue life.

Stress relieve

Low-temperature heat treatment to relieve residual stresses induced during coiling or forming, so that springs are more stable, better able to withstand higher stresses and have longer fatigue life.

T

Torque (M)

A twisting action in torsion springs which tends to produce rotation, equal to the load multiplied by the distance (moment arm) from the load to the axis of the spring body. Usually expressed in inch-ounces, inch-pounds or foot-pounds.

Torsion spring

A helical spring whose legs are rotated about the spring axis, resisting an applied torque. The wire is stressed in bending.

​

Torsion springs →

 

Total number of coils (N)

In compression springs, the sum of the active coils plus the dead coils forming the ends. In extension springs, equal to the active coils, not including the coils or material used to form the ends.

V

Variable rate spring

A spring whose rate changes as it deflects, usually by varying the pitch or coil diameter so coils close progressively under load.
 

Variable rate springs →

W

Wahl correction factor (K)

Multiplier applied to the basic torsional stress formula to account for direct shear and coil curvature: K = (4C − 1)/(4C − 4) + 0.615/C. It increases as the spring index (C) decreases.

Wire diameter (d)

Diameter of the wire used to make the spring.

Wire form

A part bent from wire into a custom two- or three-dimensional shape, such as a clip, bracket, hook or retainer, rather than coiled into a spring.
 

Custom wire forms →

FROM THE ARCHIVE

A Brief History of the Spring

Simple, non-coiled springs have been used throughout human history, the archer’s bow being one of the earliest. Bronze Age craftsmen made spring tweezers, and the Greek inventor Ctesibius of Alexandria is credited with making a springier bronze by raising its tin content and hardening the cast metal by hammering.

​

Coiled springs appeared in door locks in the early 15th century. Spring-driven clocks followed in the same century and developed into the first large watches by the 16th century.

​

In 1676 the English scientist Robert Hooke stated the principle now known as Hooke’s Law, publishing it as a Latin anagram and revealing its solution in 1678: within its elastic limit, the force a spring exerts is proportional to its deflection. It remains the basis of spring rate calculations today.

Plate from Robert Hooke’s 1678 lecture Of Spring showing a coil spring stretched by weights
Coil spring glossary PDF thumbnail

FREE DOWNLOAD

Keep the Coil Spring Glossary on Hand

All the terms on this page in a three-page printable PDF, with drawing symbols and a short history of the spring. Good for engineering teams and new buyers.

Have a Spec You're Not Sure About?

Send your print or sample and our engineers will review it, or call (920) 235-7620. Routine quotes usually come back within 3 business days.

More Spring Design Resources

Rate, load and stress for all three types.

Spring wire grades, specs and temperatures.

Answers to common design and ordering questions.

Guides, calculators and downloads.

bottom of page