top of page

Home › Capabilities › Secondary Operations & Finishing

CAPABILITIES · SECONDARY OPERATIONS

Springs hanging in paint line

Spring Secondary Operations & Finishing

Our spring secondary operations happen in-house in Oshkosh, Wisconsin: shot peening, grinding, heat treating, powder coating, wet paint, welding and fabrication. You get finished springs and wire forms, ready to assemble.

Why In-House Spring Secondary Operations Matter

UNDER ONE ROOF

icon-shorter-lead-times icon

Shorter lead times

Parts go from coiling to finishing without waiting in another vendor's queue.

icon-one-quality-system icon

One quality system

Every step covered by our ISO 9001:2015 registered system.

icon-one-purchase-order icon

One purchase order

One supplier responsible for the finished part.

icon-lower-total-cost icon

Lower total cost

No extra freight or handling between vendors.

IN-HOUSE

Our In-House Capabilities

Every operation below happens in the same Oshkosh plant where your springs are made.

springs being unloaded form shot peening machine

Shot Peening for Springs

springs being loaded into grinding machine

Spring End Grinding

springs on conveyer belt heading to heat treating

Heat treating & stress relieving

preloaded compression spring

Spring Presetting

spring on hanger heading into powder coat painting machine

In-House Powder Coating

spring on wet paint line

Wet Paint for Springs & Wire Forms

OCS employee welding wire form assembly

Welding & Light Fabrication

In-house tooling

Standard tooling on hand for most orders; special tooling built by our own toolmakers.

HOW EACH PROCESS WORKS

Secondary Operations in Detail

Here’s what each in-house process does for your springs, and when it makes sense to specify it.

Shot Peening for Springs

Shot peening blasts the spring surface with small, round steel shot. This cold-working process puts the surface in compression, which resists crack growth and can improve fatigue life several times over, depending on the design and stress level. It's a common choice for springs that cycle heavily.

​

Heat treating & stress relieving

Coiling and forming leave residual stresses in the wire that can cause early breakage. Stress relieving, a low-temperature heat treatment, relaxes those stresses so the spring holds its shape and lasts longer. Some materials also need full heat treating to reach their final properties, such as precipitation hardening for 17-7 PH stainless. We allow for any dimensional change during setup, so finished parts meet your print.

​

In-House Powder Coating

Our in-house powder coating adds corrosion protection and color to springs and wire forms. Finishing in-house gives us control over quality and timing, and makes it easy to color-match or color-code parts.

​

Welding & Light Fabrication

When a spring or wire form needs to become part of a larger component, our welding and light fabrication capabilities let us deliver fabricated spring components, not just loose parts.

​

Spring grinding flattens the squared ends of compression springs so they sit square, load evenly and resist buckling, especially over a shaft or in a bore. Because grinding adds cost, we'll help you decide whether your spring needs it. Light-wire and high-index springs often work well with squared, unground ends.

​

Spring End Grinding

Spring Presetting

A spring "takes a set" when it's stressed past its elastic limit and doesn't return to its original length. We can preset springs by compressing them to solid height during manufacturing, so they hold their length in service.

​

Wet Paint for Springs & Wire Forms

Wet paint gives you another option for color matching, color coding and corrosion protection. Painted wire forms and coated industrial springs are common in agricultural, outdoor and industrial equipment.

​

Want the terms explained?

Shot peening, stress relieving, presetting and more are defined in our free Coil Spring Glossary.

FROM WIRE TO FINISHED PART

One Plant, One Process, One Supplier

ocs-step-1 icon
ocs-step-2 icon
ocs-step-3 icon
ocs-step-4 icon
ocs-step-5 icon
ocs-step-6 icon
ocs-step-7 icon

Springs & wire forms

Coil / form

Stress relieve

Heat treat

Square ends

Grind

Shot Peen

Fatigue life

Powder / paint

Coat

Load test, vision

Inspect

Ready to assemble

Ship

THROUGH LOCAL PARTNERS

Plating & Other Finishes

For finishes we don’t apply in-house, we work with trusted local partners and manage the process for you, so you still deal with just one supplier.

High-strength spring steels need baking after plating to prevent hydrogen embrittlement. We plan for it as part of the process.

Finish

Main benefit

Zinc plating

Corrosion protection and appearance

Passivation

Corrosion resistance for stainless

Black oxide

Black appearance, mild protection

Nickel or tin

Bright appearance; tin aids soldering

Copper plating

Electrical conductivity

Rust preventive oil

Low-cost storage protection

Color dip

Part identification

FINISH SELECTION

Choosing the Right Spring Finish

Start with the environment and whether the concern is function, appearance or both. In many cases a corrosion-resistant material such as stainless steel, or pre-plated wire, costs less than plating after forming. Every finish adds some cost and lead time; outside finishes add the most. Typical lead time is 3 to 7 weeks, and we expedite when needed. Choosing the right finish early is one of the easiest ways to lower the cost of your springs.

Compare materials before you choose a coating

Our free Spring Materials Properties Guide shows corrosion resistance, temperature limits and more.

OCS Materials Guide image

Need finished springs, ready to assemble?

Tell us what your part needs. Routine quotes usually come back within 3 business days.

Shot peening, stress relieving and more, explained

Prototypes finished on production processes

Compression, extension and torsion springs and wire forms

One-source supply, no high minimums

bottom of page